Chapter selection previously only used the spine index, causing
navigation to always land on page 0 of the spine item. Sub-chapters that
share a spine file but differ by anchor (e.g. `chapter.xhtml#sec2`) were
silently ignored. Now the TOC anchor is passed through `ChapterResult`
and applied via the existing `pendingAnchor` mechanism.
## Summary
* This PR implements navigation to sub-chapters which didn't work
correctly previously. If a sub-chapter of the current top-level chapter
was selected, nothing happened. If a sub-chapter of another top-level
chapter was selected, reader switched to the beginning of the top-level
chapter.
* In addition, chapters now always start from a new page. This fixes
anchor to page calculation for the cases when the actual chapter content
doesn't fit on the page where the corresponding ToC anchor was found.
## Additional Context
* I might misuse `pendingAnchor` here which was previously used for
footnote navigation, please double check. I'm open to suggestions for
improvements.
* Note that the chapter selected by default when
`EpubReaderChapterSelectionActivity` opens is still wrong. I'm going to
fix this separately. This PR addresses only navigation to the selected
chapter.
* I tested this PR on my X4 and verified that navigation to a different
sub-chapter works correctly, both inside and outside the current spine.
* Some of the changes were borrowed from
https://github.com/crosspoint-reader/crosspoint-reader/pull/1455
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? _**PARTIALLY**_
---------
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Tiled grayscale rendering to drop the storeBwBuffer peak largest
contiguous free block (the value that actually drives OOM on the C3)
from ~114 KB to ~82-90 KB.
This renders each grayscale plane band-by-band into a small (~8 KB)
scratch and
streams each band straight to controller RAM (community-sdk
writeGrayscalePlaneStrip), leaving the BW framebuffer intact. No save,
no
restore; controller RAM is re-synced for the next differential turn
directly
from the live framebuffer.
Three writers honor the active band target so per-band re-rendering
stays cheap
and correct:
- drawPixel (text) redirects writes to the band scratch and clips to it.
- renderCharImpl skips glyphs whose physical y-extent is outside the
band before
the bitmap decode (glyphIntersectsStrip), so the per-band re-render
doesn't
pay N x glyph decode.
- DirectPixelWriter (images) writes the band scratch via getWriteTarget
instead
of the framebuffer. Without this, image pixels wrote the live BW frame
directly and cleanup re-synced that corruption, leaving thin outlines
after
navigating away from an image.
Controller specifics live in the SDK (X4 setRamArea windowing, X3 PTL);
the
reader checks supportsStripGrayscale() and is otherwise
controller-agnostic.
Measured on hardware (X4 and X3, text and images, visually correct):
- Grayscale scratch ~8 KB vs ~50 KB save; largest contiguous free block
held at
full size during grayscale instead of dropping ~25-32 KB.
- X4 text page about +25 ms/page; X3 page time is dominated by its
intrinsic
grayscale refresh, not tiling.
Depends on community-sdk #13 (the writeGrayscalePlaneStrip API). The
submodule
bump here points at that branch, so until #13 merges the submodule won't
resolve
from upstream and CI will fail there; keeping this a draft until then.
Will
rebase onto master and re-point the submodule to the merged SDK commit
once #13
lands.
Did you use AI tools to help write this code? partial
## Summary
Minor cleanup flagged by newer gcc:
- Removed unused variables
- Removed unimplemented function declaration
- `static` -> `inline` to avoid per-TU duplication
---
### AI Usage
Did you use AI tools to help write this code? _**NO**_
## Summary
* **What is the goal of this PR?** fixes#2132.
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? _**< NO >**_
With both OtaUpdater and HttpDownloader on esp_http_client
(https://github.com/crosspoint-reader/crosspoint-reader/pull/2074,
https://github.com/crosspoint-reader/crosspoint-reader/pull/2075),
checkForUpdate no longer needs its own client and event handler to fetch
the release JSON. It streams the response straight into
ReleaseJsonParser through a new HttpDownloader::fetchUrl(url,
DataCallback) overload, dropping the duplicate esp_http_client setup,
the HTTP_EVENT_ON_DATA handler, and the totalBytesReceived file global.
DataCallback hands body chunks to a callback without buffering. The
naive alternative, collecting the ~32KB JSON into a std::string, aborts
under -fno-exceptions: the growing allocation collides with the TLS
session's heap mid-fetch and operator new calls abort().
The OTA install path stays on esp_https_ota (flash-write streaming),
which has no HttpDownloader equivalent.
HttpDownloader.h must precede the lwip (esp_http_client) headers in
OtaUpdater.cpp, or Arduino/SdFat macros collide with lwip.
Did you use AI tools to help write this code? partial
Based on the learnings from
https://github.com/crosspoint-reader/crosspoint-reader/pull/2074 , I
wanted to bring the same buffer savings to the rest of our HTTP Client
stack. That being said, HttpDownloader (fonts/OPDS) used the Arduino
HTTPClient.
HttpDownloader was the last consumer of the Arduino HTTPClient +
NetworkClientSecure stack. OtaUpdater already runs on esp_http_client,
so this drops the parallel HTTP/TLS implementation. It also fixes a
class of OPDS/font download failures: HTTPClient's setTimeout is uint16
and truncates, and its short per-read deadline killed slow or chunked
responses (the -11 / incomplete-data errors).
What changed:
- Rewrote fetchUrl/downloadToFile around esp_http_client with a
streaming open() -> fetch_headers() -> read() loop, manual redirect
following, and is_complete_data_received() as the completeness gate.
Body bytes go straight to the sink (OPDS parser stream, std::string, or
file), so nothing buffers the payload.
- HTTPS is now verified against the CA bundle instead of
NetworkClientSecure::setInsecure(). esp-tls is built with
CONFIG_ESP_TLS_INSECURE off, so an unverified handshake can't be set up
anyway; the model is public servers over verified https and local
servers over plain http (transport is chosen from the URL scheme).
** Self-signed https servers are no longer supported, by design. **
- timeout_ms is 60s; esp_http_client's timeout is uint32, so unlike
HTTPClient it doesn't silently truncate.
- HTTP buffers are 4096 (rx) / 1024 (tx). 4096 holds real OPDS server
headers; the GitHub release CDN sends more and logs a non-fatal
truncation warning, but the headers we read (Location, Content-Length)
come first and survive.
- Removed the now-unused UrlUtils::isHttpsUrl and a stale HTTPClient
comment in FontDownloadActivity.
Validated on device: OPDS browse and a 3.4 MB book download over
verified https, GitHub font downloads (crc-checked), redirect handling
matching curl, and slow/erroring servers surfaced correctly.
Did you use AI tools to help write this code? partial
## Summary
### **What is the goal of this PR?**
This fixes an unintended settings side effect when cycling the `Sleep
Screen` option through `Quick Resume`.
Previously, selecting `Sleep Screen = Quick Resume` globally forced
`Quick Resume on Timeout = ON` and left it enabled even after the user
toggled `Sleep Screen` to another option within the same settings
session. Now the auto-enable behavior is scoped to the Settings screen
session:
- If `Quick Resume on Timeout` was already `ON` when entering Settings,
it stays `ON`.
- If it was `OFF`, selecting `Sleep Screen = Quick Resume` temporarily
turns it `ON`.
- If the user then switches away from `Quick Resume`, it turns back
`OFF`.
### **What changes are included?**
- Removes the global logic that permanently forced `Quick Resume on
Timeout` to `ON` whenever `Sleep Screen` was set to `Quick Resume`, even
if it was just due to toggling through the options.
- Adds Settings-screen session tracking so `Quick Resume on Timeout` is
only auto-enabled while the user has `Sleep Screen = Quick Resume`.
- Restores `Quick Resume on Timeout` back to `OFF` when the user
switches away, but only if it was `OFF` when they entered Settings.
- Preserves existing `ON` timeout preferences.
- Same behavior applies to the web settings
## Additional Context
- Tested this on device and via the settings UI
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it helps set the right
context for reviewers.
Did you use AI tools to help write this code? _**< YES >**_
Unify the two splash-skip signals (RTC silent-reboot flag, SD
seamless-sleep flag) into one BootResume enum driving a single switch.
Storage unchanged; behavior-preserving apart from the fix.
Holding power to sleep from a WiFi activity (Font Download, OPDS, web
server, Calibre, KOReader sync) rebooted to home instead of sleeping.
goToSleep() runs the outgoing activity's onExit(), and those activities
call silentRestart() to clear heap fragmentation, so the heap-defrag
reboot fired before deep sleep could start.
enterDeepSleep() now latches deepSleepInProgress before goToSleep();
silentRestart()/silentRestartToReader() no-op while it's set. Deep sleep
is a full chip reset on wake, so it already clears the fragmentation the
reboot existed for.
Did you use AI tools to help write this code? partial
## Summary
**What is the goal of this PR?**
Adds a clearer Quick Resume sleep-screen flow. The previous “Page as
Sleep Screen” behavior is now exposed as a dedicated `Sleep Screen >
Quick Resume `option, with the timeout-only behavior controlled by a
renamed `Quick Resume on Timeout `setting.
**What changes are included?**
- Adds `Quick Resume` as a new `Sleep Screen` option.
- Renames the old `Page as Sleep Screen` setting to `Quick Resume on
Timeout`.
- Changes that setting’s choices from `Never / After Timeout / Always`
to `OFF / ON`.
- Makes `Quick Resume on Timeout = ON` equivalent to the old `After
Timeout` behavior.
- Makes `Sleep Screen > Quick Resume` equivalent to the old `Always`
behavior.
- Automatically forces `Quick Resume on Timeout` to `ON` when `Sleep
Screen` is set to `Quick Resume`.
- Renames internal setting references from `seamlessSleepScreen` to
`quickResumeSleepScreen`.
- Updates translations for the renamed setting label.
**Additional Context**
- This is mostly a settings/labeling restructure around existing
behavior, not a new rendering path.
- The runtime quick-resume behavior still uses the existing saved
framebuffer / last-screen sleep flow.
- Review focus areas:
- Sleep entry behavior from manual sleep vs timeout sleep.
- The automatic dependency where selecting `Sleep Screen > Quick Resume`
sets `Quick Resume on Timeout` to `ON`.
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? _**< YES >**_
---
**New `Quick Resume` option for `Sleep Screen` will automatically set
`Quick Resume on Timeout` to `ON`**:
<img width="480" height="800" alt="quick resume"
src="https://github.com/user-attachments/assets/94c553fd-a122-47a8-add9-f29694f55566"
/>
**Example where a different sleep screen setting like `Cover` can be
used in combination with the `Quick Resume on Timeout` setting**:
<img width="480" height="800" alt="cover + quick resume"
src="https://github.com/user-attachments/assets/dd18ce18-230b-4b78-808b-ac85f5e7d5d8"
/>
## Summary
Previously `ScreenshotUtil` used physical display size to draw a border
around the screen contents. Because of this, in landscape orientation
the border was shown as a broken square. This PR changes border drawing
to use logical screen size instead of a physical display size to take
orientation into account.
## Additional Context
* Tested on X4 in all 4 reading orientations. Behavior is now correct,
however it doesn't look perfect on my X4: the border is much closer to
the physical top side of the display than to the other sides. This might
be related to assembly variation during manufacturing, but it might as
well be related to the way a eink controller is connected to the display
(controller supports bigger display sizes, so an offset may be present).
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? _**NO**_
## Summary
After a silent reboot, there was a small window where the esp32 would
listen for button presses but the full refresh would hold the event
loop. This gave a UX experience where the silent reboot had completed to
the home screen, a user taps select (at any time during the process),
and they find themselves unexpectedly in a book.
## Additional Context
This must land after
https://github.com/crosspoint-reader/community-sdk/pull/11 and will need
the submodule SHA changes included in.
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? partially
OTA install streams the full 5.8MB image over a multi-minute TLS session
while wifi/LWIP already holds the big internal arena. Measured on
device, the arena bottomed out at ~7.7KB free with the largest
contiguous block down to ~2.4KB; for 80% of the download there wasn't
even a contiguous 8KB block. It finishes on a clean heap but tips into
OOM for anyone carrying more pre-OTA fragmentation.
Two avoidable drains, both in OtaUpdater:
- The esp_http_client RX/TX buffers were 8192/8192 on both the version
check and the install. RX only has to hold response headers (bodies
stream through the parser / OTA writer) and TX only carries our GET, so
trim both to 4096/1024. 4096 still fits the github->CDN redirect
headers; the 512 IDF default truncates them, which is why they got
oversized in the first place.
- installUpdate fired the progress callback every ~100ms perform
iteration, waking the render task on every tick. Its framebuffer work
fights the TLS session for the same arena, and epd can't really repaint
faster than a percent anyway. Throttle it to whole-percent changes.
On device, combined: floor 7.7KB -> 19KB, worstcase contiguous block
2.4KB -> 21KB, zero sub 8KB iterations across the whole download.
KOReaderSyncClient already uses small buffers; HttpDownloader is on the
Arduino HTTPClient stack with no equivalent knob, so neither changed.
Did you use AI tools to help write this code? partial, heap-exploration
assisted by Claude.
setTimeout(0) on the serial could trigger a subtle but obnoxious
underflow.
Eat a milli, save a reset button.
Did you use AI tools to help write this code? no
<img width="605" height="454" alt="image"
src="https://github.com/user-attachments/assets/bfd84afe-3b58-436e-9a5d-539af3ec3d4e"
/>
Actualized "Last" sleep screen setting from previous PRs, rebranded as a
~~`Seamless Sleep`~~ `Page as Sleep Screen` option with more
improvements.
https://github.com/user-attachments/assets/59029ba6-007e-4841-abfa-f680d7e98b79
---
New option: `Page as Sleep Screen` - `Never (default)`, `After Timeout`,
`Always`
When enabled, it seamlessly sleeps on timeout or power off, making a
fast refresh for the moon icon. When waking up, we still show the last
page, instead of the boot screen, making it fully seamless.
I tried different icons such as "refresh arrow" and others, but they
looked not as nice as 3 simple dots.
With this mode, the device turns off 4 seconds faster. And has 6 seconds
less delay when turning back on. Much more responsive.
Previously, even a 10-minute timeout sometimes wasn't enough, and I'd
worry about seeing the book cover. It's now easier to use a shorter
sleep timeout: if I get distracted during a reading session but don't
want to stop, the new screen is much more inviting to come back to.
---
Did you use AI tools to help write this code? _**PARTIALLY**_.
---
Test v1.3.0 firmware.bin file
[download](https://github.com/user-attachments/files/28015193/firmware.zip)
Based on PRs #410 and #495Closes#400, #1649
---------
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
When the device went into deep sleep while plugged into USB, a
power-button press would occasionally not wake it. The display held its
last frame, the chip stayed in deep sleep, and recovery required an
unplug + reset + hold-power cycle. On battery the symptom never surfaced
because the power button physically re-energises the chip.
Two peripherals were holding power domains alive across the deep sleep
boundary and interfering with the configured GPIO wake on the power
button:
1. HWCDC. Once Serial is initialized, the USB Serial/JTAG peripheral
keeps its power domain configured even with TX timeout at zero and no
host draining. Tear it down with Serial.end() in
HalPowerManager::startDeepSleep, gated by ENABLE_SERIAL_LOG to match the
Serial.begin site. This hit me if I was charging off my computer.
2. WiFi. enterDeepSleep had no WiFi teardown, so sleeping from any
network-using activity left the modem domain alive. Call
WiFi.disconnect(true) + WiFi.mode(WIFI_OFF) when WiFi is active. Wake
from deep sleep is effectively a chip reset, so no WiFi state needs to
survive. While this doesn't cause higher power drain, it apparently was
causing issues where I'd occasionally have the chip hang on sleep
transition from a wifi activity.
Confirmed on device.
Did you use AI tools to help write this code? partial
## Summary
* **What is the goal of this PR?** Small UX improvement to the Home
screen by preserving the last selected cursor position when returning to
it.
It supersedes #985 and #1103, which are both significantly outdated and
hundreds of commits behind master.
---
### AI Usage
Did you use AI tools to help write this code? _**< YES >**_
On-device repro showed the cover snapshot pinning ~52KB of contiguous
heap (cloning the full 48KB framebuffer with malloc overhead). MaxAlloc
on Home was 61KB; nothing was leaving headroom for HTTPS, which needs
30-50KB contiguous for the mbedTLS handshake.
Add region-aware framebuffer helpers to GfxRenderer that translate a
logical rect through rotateCoordinates and copy only the byte range that
contains the rotated rect. HomeActivity records the tile rect it passes
to drawRecentBookCover and caches only that subregion.
Measured on device (X3, Portrait):
Idle on Home | Free 102K -> 139K | MaxAlloc 61K -> 115K
Mid-EPUB-read | Free 81K -> 134K | MaxAlloc 70K -> 115K
Cover cache | ~52K -> ~16K (per allocation)
Works in all four orientations because the bounds helper samples the
four logical corners through the existing rotation, so the cached byte
range always covers the pixels the theme could have drawn into.
Savings will vary with theme, but should be significant across all.
The "logs only flow if you unplug and replug the USB cable at the right
moment" symptom traced to two interacting problems with the ESP32-C3 USB
Serial/JTAG controller (HWCDC):
1. Serial.begin was gated on gpio.isUsbConnected(). That check sampled
USB state at one specific microsecond during boot. If USB enumeration on
the host hadn't completed by that moment (common after a reset that
auto- reconnects a moment later), Serial was never initialized and
stayed dead until the next boot where the timing happened to win.
2. HWCDC writes block for up to the configured TX timeout (default 250
ms) when the host has the port open but isn't actively draining — a
state the macOS USB CDC stack enters intermittently after reconnect. The
firmware then appears to hang on logging until a USB unplug+replug
cycles the peripheral and flushes the TX FIFO.
Fix: move the Serial init to the very top of setup() with a 250 ms stall
before Serial.begin (lets the USB peripheral power-on and host
enumeration complete on cold boot), and call logSerial.setTxTimeoutMs(0)
so writes drop bytes harmlessly when the host is slow instead of
stalling the firmware. Both warm reboot and cold power-on now produce
logs immediately.
Did you use AI tools to help write this code? partial
## Summary
Add ability to long press 'confirm' on a book in the recent books list
to be prompted to remove it from the list.
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? *Yes, Claude*
---------
PR #1908 silent-restarts on exit from any wifi-using activity to defuse
LWIP/mbedTLS heap fragmentation, but two of the wifi-using paths slipped
through that audit:
KOReaderAuthActivity (Settings -> KOReader sync -> Authenticate)
OtaUpdateActivity (Settings -> Check for update, back-out paths)
Both used WiFi.disconnect + WiFi.mode(WIFI_OFF) on exit and returned
control to Settings, leaving ~50KB of contiguous heap stranded for the
rest of the session.
Mirror the FontDownloadActivity pattern: if WiFi was activated,
disconnect and silentRestart. OTA's success path is unchanged:
SHUTTING_DOWN already calls plain ESP.restart() so the new firmware
boots normally; only the cancel/fail/no-update back-out paths now go
through silentRestart().
Did you use AI tools to help write this code? partial
## Summary
* **What is the goal of this PR?**
Fix EPUB optimization when XHTML image references are URL-encoded.
* **What changes are included?**
The optimizer already converts image files to `.jpg`, but XHTML files
could still reference the original URL-encoded image path, for example:
```html
<img src="images/wensday%201%20full%202.png">
````
The optimized EPUB then contained the converted file:
```text
images/wensday 1 full 2.jpg
```
but the XHTML still pointed to the old `.png`, so CrossPoint failed to
extract/render the image.
The issue was that the previous replacement logic matched only the plain
filename form, such as:
```text
wensday 1 full 2.png
```
but not the URL-encoded form:
```text
wensday%201%20full%202.png
```
This PR updates XHTML image `src` attributes through the existing
DOMParser pass by decoding and resolving the image path before matching
it against renamed images.
After this fix, the optimized EPUB correctly rewrites the XHTML image
reference to the generated `.jpg`, and the image renders correctly.
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? _**PARTIALLY**_
---
Please let me know if you have questions,
Thank you!
## Summary
* **What is the goal of this PR?**
Fix incorrect power button long-press detection during shutdown/wake
verification by introducing dedicated power button timing logic.
* **What changes are included?**
* Added getPowerButtonHeldTime() to HalGPIO as a wrapper over input
manager logic
* Replaced generic getHeldTime() usage with power-button-specific timing
in verifyPowerButtonWakeup()
* Ensures shutdown/wake decision is based only on actual power button
hold duration, not any-button timing
* Minor header update for new API exposure in HalGPIO.h
## Additional Context
This fixes a bug where holding another button while briefly pressing the
power button could incorrectly trigger shutdown behavior due to shared
timing state (getHeldTime()).
The change isolates power button timing to prevent cross-button
interference and makes shutdown logic reliable during multi-button
interactions.
No behavioral changes are expected outside of power-button handling
logic.
**Dependencies**
- SDK PR: https://github.com/crosspoint-reader/community-sdk/pull/3
This PR requires the `community-sdk` submodule to be updated after the
SDK change is merged.
- Fixes: #1881
---
### AI Usage
Did you use AI tools to help write this code? _**PARTIALLY**_
## Summary
* **What is the goal of this PR?**
Improve the UI based on feedback from someone on discord
> Downloading ALL fonts feature.
> 1.1 Disable sleep when downloading, in my case went directly to sleep
just right after downloading.
> 1.2 It would be great to have and overall progress indicator as we
only have the indication of each font family
> 1.3 Any cancel or pause function might come in handy in case battery
is running out and then resume or retry with pending fonts
* **What changes are included?**
- Now the UI can show overall progress across every file being
downloaded in the batch, not just progress inside the current family.
- Extended `HttpDownloader::downloadToFile()` to accept a cancel flag
and abort the download.
- Rendered a cancel button in the font download UI while a download is
in progress.
- `preventAutoSleep()` in `FontDownloadActivity.h` now returns true for
`state_ == COMPLETE` and `state_ == ERROR` in addition to
`LOADING_MANIFEST` and `DOWNLOADING`
## Additional Context
Not very satisfied with how `HttpDownloader.cpp` is right now, might try
to refactor it after v1.3.0
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? _**PARTIALLY**_
WiFi/LWIP/netif teardown scatters long-lived allocations across the
heap, leaving ~50KB of contiguous space unrecoverable without a reboot.
Reboot the SoC on exit from any wifi-using activity to guarantee a clean
heap. An RTC_NOINIT flag survives the reboot and tells setup() to skip
the boot splash and route the user back where they came from:
- File transfer / Calibre / OPDS / Font download -> home
- KOReader sync -> currently-open EPUB
Activities check WiFi.getMode() before rebooting, so backing out of the
network mode menu without joining doesn't trigger a cycle. KOSync also
esp_wifi_stop()s after the sync result so the radio is off while the
user reads it; full teardown happens at the reboot.
## Additional Context
The silent reboot skips the booting splash screen - it visibly looks
like a screen refresh. This does cause a disconnection/reconnection blip
for developers actively pulling logs over serial, but `pio device
monitor` and the like successfully reconnect and feed in the early boot
serial.
as an example:
```
[256676] [DBG] [ACT] Exiting activity: KOReaderSync
[256706] [DBG] [MAIN] Silent restart (target=reader)
ESP-ROM:esp32c3-api1-20210207
Build:Feb 7 2021
rst:0xc (RTC_SW_CPU_RST),boot:0xf (SPI_FAST_FLASH_BOOT)
Saved PC:0x403872bc
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fcd72a0,len:0x990
load:0x403cbf10,len:0xac8
load:0x403ce710,len:0x4d28
entry 0x403cbf10
[22] [INF] [MAIN] Hardware detect: X4
[29] [SD] SD card detected
[43] [DBG] [CPS] Settings loaded from file
[58] [DBG] [KRS] Loaded KOReader credentials for user: jeremydk
[69] [DBG] [OPS] Loaded 1 OPDS servers from file
[69] [DBG] [UI] Using Lyra theme
[70] [DBG] [MAIN] Starting CrossPoint version 1.2.0-dev-detached-bde75787
...
[203] [DBG] [ACT] Entering activity: Reader
[211] [DBG] [EBP] Loading ePub: /Halting State - Charles Stross.epub
[221] [DBG] [BMC] Loaded cache data: 51 spine, 41 TOC entries
[246] [DBG] [CSS] Loaded 41 rules from cache
[247] [DBG] [EBP] Loaded ePub: /Halting State - Charles Stross.epub
```
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? _PARTIALLY_
## Summary
SD card font fixes:
- `TxtReaderActivity` needs to call `renderer.ensureSdCardFontReady` to
build the advance lookup table to support rendering with SD card fonts.
This revealed that `TxtReaderActivity` was inconsistently performing
layout with `getTextWidth`, when the renderer actually uses
`getTextAdvanceX`, which can lead to minor inconsistencies in alignment.
- Avoid allocating one big `allText` string in
`ParsedText::layoutAndExtractLines`. Instead, pass the vector of word
strings directly to `SdCardFont::buildAdvanceTable`, where the algorithm
just needs to iterate codepoints anyway.
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? _**PARTIALLY**_
---------
Co-authored-by: Justin Mitchell <justin@jmitch.com>
## Summary
Deleted two unused header files containing binary icon data.
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? _**NO**_
## Summary
First of several changes to decouple and clean up SD card fonts
integration. This change eliminates SdCardFontGlobals.h:
- Simply declare the `extern SdCardFontSystem sdFontSystem` in
SdCardFontSystem.h.
- `ActivityManager::goToReader` should not care about loading SD card
fonts. Instead do the same work in `ReaderActivity::onEnter`, after the
previous activity has exited and after ReaderActivity has validated the
file path.
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? _**NO**_
## Summary
Relative includes can hide inappropriate dependency relationships. In
this case, I found that lib/KOReaderSync/KOReaderCredentialStore.cpp was
dependent on src/JsonSettingsIO.h -- a lib -> app dependency, the
opposite direction dependencies should flow in this project.
This change replaces all relative includes with root-relative includes,
and corrects the KOReaderCredentialStore dependency by moving its JSON
settings serialization local to the KOReaderSync library.
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? _**PARTIALLY**_
## Summary
- Holding the navigation button in **Settings → Reader → Font family**
now advances the selection by a full visible page instead of one item at
a time.
- Same fix applied to **Settings → Language**, which had the same
one-item-only behavior.
- Mirrors the pattern already used in font download (ceb3fed) and
chapter selection screens.
## Test plan
- [ ] Settings → Reader → Font family: tap moves by one item; hold jumps
a page (wraps at ends)
- [ ] Settings → Language: tap moves by one item; hold jumps a page
(wraps at ends)
## Summary
* **What is the goal of this PR?**
Separate the font manager's combined `Download / Update All` action into
separate `Download All` and `Update All` rows
* **What changes are included?**
- Updated multiple i18n translation files to add `STR_UPDATE_ALL` and
adjust `STR_DOWNLOAD_ALL` text.
- Added separate handlers: `downloadAll()` for fonts that have been
installed and `updateAll()` for fonts with updates.
- `Download All` and `Update All` are only shown when applicable.
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? _**PARTIALLY**_
## Summary
Bind `prev` / `next` functionality to the left and right buttons in BMP
Viewer and adds labels
<img width="718" height="953" alt="image"
src="https://github.com/user-attachments/assets/c6dac14e-14f5-4cbf-9298-772cfc479f33"
/>
## Additional Context
* Add any other information that might be helpful for the reviewer
(e.g., performance implications, potential risks,
specific areas to focus on).
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? _**NO**_
Reverts crosspoint-reader/crosspoint-reader#1912
This was meant to be more robust with partial SD card fonts, but causes
trouble for folks using custom font sizes. We need a better approach to
decouple numeric font sizes from S/M/L/XL settings.
## Summary
* **What is the goal of this PR?**
1. Adds font family deletion support to the font download activity so
users can remove installed font families directly from the download
list.
2. Address an issue where a font family manually deleted in the file
browser by user will show as "update" in the `FontDownloadActivity`
* **What changes are included?**
* Updated button hint label to show `Delete` when deletion is available.
* Added confirmation before deleting a selected installed font family.
* Refreshed font registry in `fetchAndParseManifest` (for the second
goal above)
---
### AI Usage
While CrossPoint doesn't have restrictions on AI tools in contributing,
please be transparent about their usage as it
helps set the right context for reviewers.
Did you use AI tools to help write this code? _**PARTIALLY**_
